Since 1947

Orders over $30 Get up to

      15% off!
Tier Discount. The more you purchase, 
the more you save.  All items qualify!



Shop by category
Shutter Clips for Vinyl Shutters 12/bag
Email a friendView larger image

Shutter Clips for Vinyl Shutters 12/bag

Our Price: $15.90


In Stock
Usually ships in 4-5 business days
Product Promotions:
  • Tier Discount. Up to 15% OFF all orders over $30 on Capitol City Lumber's products! The more you buy, the more you save! All products apply.  Here's how (restrictions apply)

Universal shutter clips for vinyl shutters. Each bag contains 12 shutter clips. Shutters tend to expand and contract with normal daily temperature changes. Make sure there is at least 3/4" space for movement both above and below the shutter. It is recommended that all mounting clips be free to move vertically. These shutter clips can be mounted on wood, vinyl, aluminum, brick, stone or block exteriors. Masonry anchors are included. Use the masonry anchors included and screws (not included) for masonry exteriors. Use a 5/16" masonry drill bit for masonry applications. For vinyl and aluminum siding, drill a 1/4" hole through siding to allow siding to move. Using a 9/64" drill bit, drill into wall substrate. Use (4) four clips per shutter sizes up to 55". For sizes 59" through 81", it is recommended to use two extra clips per shutter in center of shutter. Shutter clips and masonry anchors are included, as pictured above. Screws and drill bits are not included.


Shutter clips for vinyl shutters.

Invisible clip mount

Clip part is 3/4" deep, 3/4" tall ann 5/16" wide

Clip's overall height is 1-5/8", including the eye.

Sold 12 shutter clips per bag.

Product Details:
Average Customer Rating: based on 12 reviews
Customer Reviews:
Average Customer Review: 4.0 ( 12 customer reviews )
Write an online review and share your thoughts with other customers.

Most Helpful Customer Reviews

1 of 1 found the following review helpful:

4I hug 6 shutters in a little over an hourJan 07, 2013
By Tony DiTola
Going into a concrete wall, these little jobbers made installation a snap. I've never used anything like them before, but after one shutter was up, I moved pretty quickly.

My only concern is that the clips aren't sliding like I had hoped they would. I put black vinyl shutters on the south side of my house. Since they get a lot of sun, they expand as they get warm. I was hoping the slotted screw hole would allow them to expand without bending. Not so much. I guess I could loosen the screws a bit more, but then they tend to swing around as I put the shutter up and they can be difficult to get lined up properly. I'll have to play around with them more in the spring.

1 of 1 found the following review helpful:

5Did the trickFeb 02, 2012
By L. Marinaro
My shutters kept falling down with even a small breeze. I had to buy these online because none of the local stores had them or knew anything about them. They all recommended screws. I used the clips to reattach the shutters and they have been up ever since. We've even had a few good storms.

1 of 1 found the following review helpful:

1Waste of moneyOct 01, 2009
By S. Lee
Was not able to use them because the clips were to tight and I couldn't ajust them. Didn't send them back because the shipping cost from Capitol City Lumber were so wasn't worth it. Total waste of money.

1 of 1 found the following review helpful:

4Qick shippingJan 30, 2010
By Guzzi
Good product but smaller than I originally thought. Need to have size in specs. because pix make them look bigger.

1Did not workJun 27, 2014
By afitz
They did not work for the shutters we have, from the 60s. They don't seem to make replacement parts for anything "old".

See all 12 customer reviews on
About Us   Contact Us
Privacy Policy Copyright © , Capitol City Lumber. All rights reserved.
Web business powered by Amazon WebStore